Introduction to MP 4M 3000 mPas Low Viscosity HPMC For Ceramic Extrusion Direct

Hidroksipropil metilceluloza (HPMC), čiji je kineski naziv hidroksipropil metilceluloza, je polusintetika, nejonski eter celuloze dobijen hemijskom modifikacijom prirodne celuloze. Ovaj bijeli prah može formirati prozirnu viskoznu otopinu nakon rastvaranja u vodi. Ima odlično zgušnjavanje, zadržavanje vode, stabilnost i svojstva stvaranja filma. To je nezamjenjiv multifunkcionalni aditiv u mnogim poljima kao što je građevinarstvo, lijek, i hranu.

Characteristics and advantages of MP 4M 3000 mPas Low Viscosity HPMC For Ceramic Extrusion Direct

Odlična rastvorljivost u vodi: Može se brzo otopiti u hladnoj vodi kako bi se formirala bistra i stabilna otopina.

Efikasno zgušnjavanje i sposobnost zadržavanja vode: Povećajte viskozitet materijala, efikasno smanjuju isparavanje vode, i poboljšati radnu efikasnost.

Dobra stabilnost: Ima dobru stabilnost na kiseline, alkalije, i soli, i pogodan je za širok raspon pH vrijednosti.

Filmotvorni i zaštitni efekti: Nakon sušenja, formira čvrst i proziran film koji štiti podlogu i sprečava prodiranje vode i isparavanje.

Netoksičan i neiritantan: Ima dobru biokompatibilnost i pogodan je za područja medicine i hrane.

Prilagodljivost: Promjenom stepena supstitucije i molekularne težine, njegove performanse se mogu prilagoditi kako bi zadovoljile različite zahtjeve primjene.

Specification of MP 4M 3000 mPas Low Viscosity HPMC For Ceramic Extrusion Direct

MP 4M 3000 mPa · s Low Viscosity HPMC for Ceramic Extrusion

Premium Binder for Smooth, Constant Ceramic Forming

MP 4M 3000 mPa · s is a specifically developed hydroxypropyl methylcellulose (HPMC) made for ceramic extrusion procedures. It uses low thickness at 3000 milipaskalne sekunde (mPa · s), which aids attain attire flow and easy shaping of ceramic bodies.

This HPMC quality dissolves quickly in chilly water. Razvija jasno, steady option that uniformly coats ceramic bits. The result is better plasticity and reduced friction throughout extrusion. This causes smoother surface area coatings and less flaws in the final greenware.

Tajne prednosti se sastoje od:
– Enhanced green strength without endangering workability
– Minimized pass away swell and better dimensional control
– Marginal air entrapment during mixing and developing
– Superb compatibility with common ceramic basic materials like clay, feldspar, i silicijum dioksid

MP 4M 3000 mPa · s carries out well throughout a range of moisture components. It maintains regular rheology also under differing production conditions. This makes it trustworthy for both small-batch workshops and large-scale production lines.

The item contains no included salts or surfactants. It stresses out cleanly throughout firing, leaving no deposit that might influence shade or thickness. This tidy exhaustion supports high-grade sintering and lowers the danger of bloating or cracking.

Prostor za skladištenje je jednostavan– keep the powder in a dry, amazing area away from moisture. Jednom otvoren, reseal the container securely to stop clumping.

Manufacturers choose MP 4M 3000 mPa · s since it provides predictable results batch after batch. It lowers waste, accelerate manufacturing, and aids create porcelains with sharp information and structural stability right from the extruder.

Applications of MP 4M 3000 mPas Low Viscosity HPMC For Ceramic Extrusion Direct

Applications of MP 4M 3000 mPa · s Low Viscosity HPMC in Ceramic Extrusion

Smooth Flow, Consistent Forming

MP 4M 3000 mPa · s is a low thickness grade of Hydroxypropyl Methylcellulose (HPMC) created ceramic extrusion. It aids damp clay bodies relocate easily via passes away without blocking. This maintains the shape of tiles, tubes, or accounts stable throughout developing.

Better Workability and Green Stamina

This HPMC offers eco-friendly bodies adequate strength to hold with each other after extrusion however prior to firing. It reduces splitting and deforming during handling and drying out. Potters and makers obtain less rejects and smoother production runs.

Attire Water Retention

MP 4M holds water equally throughout the clay mix. That suggests no dry areas or soft zones. Drying out takes place at the same rate all over. This cuts down on stress inside the item and stops surface area defects.

Clean Fatigue, No Residue

The additive burns out fully throughout the beginning of shooting. It leaves no ash or carbon behind. Final products stay pure in shade and strong in framework.

Lako se miješa i koristi

You can mix MP 4M into common ceramic dishes without changing your procedure. It blends fast in water and works well with typical clays like kaolin, ball clay, and feldspar. Just add the correct amount– obično 0.2% to 0.8% po težini– a ti se spremaš da ideš.

Trustworthy Throughout Set Sizes

Whether you run little craftsmen batches or huge commercial lines, this HPMC does the very same every single time. Its regular top quality indicates you don’t require to adjust settings in between work.

MP 4M 3000 mPa · s HPMC is built for real-world ceramic extrusion. It solves day-to-day troubles like bad flow, weak environment-friendly components, and uneven drying out– without including steps or expense.

Predstavljanje kompanije

Dobrodošli u Concrete and More, vodeći dobavljač dodataka za beton visokih performansi, uključujući naše vrhunske betonske reduktore vode. Sa dugogodišnjim iskustvom na globalnom tržištu, nudimo napredna rješenja dizajnirana da poboljšaju kvalitetu i efikasnost građevinskih projekata širom svijeta. Naši vrhunski proizvodni pogoni osiguravaju proizvode vrhunskog kvaliteta koji zadovoljavaju međunarodne standarde. Ponosimo se izuzetnom uslugom za korisnike, tehnička podrška, i rješenja prilagođena specifičnim potrebama projekta. Partner sa nama za pouzdan, inovativan, i isplativi dodaci betonu koji pokreću vaše projekte naprijed. Istražite više na www.concreteandmore.de/. Gradimo budućnost zajedno!

Ako imate bilo kakvih pitanja, slobodno nas kontaktirajte.

Načini plaćanja

T/T, Western Union, Paypal, Kreditna kartica itd.

Metode isporuke

Zrakom, morem, ekspresno, po zahtevu kupaca.

5 FAQs of MP 4M 3000 mPas Low Viscosity HPMC For Ceramic Extrusion Direct

FAQs: MP 4M 3000 mPa·s Low Viscosity HPMC for Ceramic Extrusion

What is MP 4M 3000 mPa·s HPMC used for?

This HPMC grade works well in ceramic extrusion. It gives green bodies enough strength before firing. The low viscosity helps mix the clay evenly. This makes shaping easier and reduces defects.

Why choose low viscosity HPMC like MP 4M?

Low viscosity means the powder mixes fast and spreads evenly in water. It does not make the slurry too thick. That keeps the ceramic paste smooth and easy to push through dies. You get consistent shape and surface finish.

How much MP 4M should I add to my ceramic body?

Most users add 0.3% to 1.0% by dry weight. The right amount depends on your clay type and process. Počnite s malom probnom serijom. Adjust based on how the extrudate holds its shape and dries.

Does this HPMC affect drying or firing?

MP 4M burns out cleanly during firing. It leaves little to no ash. This lowers the risk of cracks or bloating. It also slows drying a bit, which helps prevent warping and shrinkage cracks.

Is MP 4M compatible with other additives?

Da. It works well with common plasticizers, deflocculants, i veziva. Just add it after wetting other powders. Mix thoroughly to avoid lumps. Always check compatibility with a small trial first.